Comprehensive two-dimensional liquid chromatography with inductively coupled plasma mass spectrometry detection for the characterization of sulfur, vanadium and nickel compounds in petroleum products.

The petroleum industry is increasingly concerned with the conversion of vacuum residues as a consequence of decreased conventional crude oil availability. The compositional analysis of heavy oil products has become a key step in conversion processes, but the complexity of these oil matrices tends to increase with their boiling point. In this study, comprehensive two-dimensional liquid chromatography (LCxLC) coupled to inductively coupled mass spectrometry (ICP-MS/MS) is considered with a view to meet new requirements and to bring additional information regarding the species present in these matrices. In search for a high degree of orthogonality, two separation techniques involving two different retention mechanisms were evaluated: Size Exclusion Chromatography (SEC) and Reverse Phase Liquid Chromatography (RPLC). In SEC, the analytes are separated according to their molecular weight while according to their hydrophobicity in RPLC. The separation power of both individual separation techniques was first evaluated. Off-line and on-line LCxLC were compared on the basis of an optimization approach. It is shown that off-line SECxRPLC can provide, for the same analysis time of 150 min, a higher peak capacity (2600 vs 1700) than on-line RPLCxSEC while a similar dilution factor (close to 30) but also requires far fewer fractions to be analyzed (12 vs 400). Asphaltenes which constitute the heaviest fraction of crude oils (obtained from petroleum industry) were analyzed by the developed off-line SECxRPLC method. The resulting 2D-contour plots show that co-elutions could be removed leading, for the first time, to new information on high molecular weight species containing sulfur and vanadium.

Suitable interface for coupling liquid chromatography to inductively coupled plasma-mass spectrometry for the analysis of organic matrices. 2 Comparison of Sample Introduction Systems.

Liquid chromatography (LC) coupled with a specific detection such as inductively coupled plasma-mass spectrometry (ICP-MS/MS) is a technique of choice for elementary speciation analysis for complex matrices. The analysis of organic matrices requires the introduction of volatile solvents into the plasma which is an analytical challenge for this coupling technique. Detection sensitivity can be significantly affected by instrumental limitations. Among those, we were interested in the solute dispersion into the interface located between LC and ICP-MS/MS. This interface consists in both a Sample Introduction System (SIS) and a possible flow splitter. This study, divided into two parts, investigated the analytical performance (in terms of sensitivity and efficiency) generated by the coupling of LC and ICP-MS in the specific case of organic matrices. In Part I [1], we previously discussed the impact of extra column dispersion on the performance of LC-ICP-MS, first from a theoretical point of view and next, by assessing extra-column dispersion in 55 published studies on LC-ICP-MS. It was shown that SIS was rarely optimized with respect to its contribution to extra-column band broadening. The critical impact of flow splitting on extra-column dispersion was also pointed out. The present Part II is dedicated to the experimental comparison of commercially available SIS by assessing extra-column band broadening and hence the contribution of SIS to the loss in both efficiency and sensitivity. It is shown that the peak variance, due to SIS, can vary from 10 to 8000 µL² depending on the combination of both nebulizer and spray chamber. Whereas the highest values (i.e. > 2000 µL²) are much too high in high performance liquid chromatography (HPLC), even the lowest values (i.e. < 100 µL²) can be inappropriate in ultra-high pressure liquid chromatography (UHPLC) as highlighted in this study. In light of these results, it appears that nebulizer and spray chamber have to be chosen together with respect to the chromatographic technique (HPLC or UHPLC) and that both peak dispersion and peak intensity depend on key parameters including SIS device geometry, flow rate entering the interface or spray chamber temperature.

Biomonitoring chronic lead exposure among battery manufacturing workers in Tunisia.

The aim of the study was the biomonitoring of the chronic exposure to Pb by measuring its levels in blood, urine, and hair of battery workers. Blood lead (BPb), urinary lead (UPb), hair lead (HPb), and urinary δ-aminolevulinic acid (UALA) levels were determined for 52 workers in a battery plant and compared to those of 20 non-occupational exposed subjects (controls). BPb and UPb levels were determined by graphite furnace atomic absorption spectrometry (GFAAS). HPb levels were measured by triple quadrupole ICP-MS and UALA levels were determined using cation exchanger column. The measured levels were significantly higher compared to the controls exceeding the OSHA cutoff values (p < 0.01). The GM mean levels of BPb, UPb, UALA, and HPb of workers were 715 µg L-1, 331 µg L-1, 16.3 mg g-1, and 234 µg g-1, respectively. The GM mean levels of BPb, UPb, UALA, and HPb of controls were 93.6 µg L-1, 36.3 µg L-1, 1.9 mg g-1, and 1.8 µg g-1, respectively. Significant correlations were observed between BPb and UALA (r = 0.630, p = 0.000), UPb and UALA (r = 0.566, p = 0.000), and between BPb and HPb (r = 0.466, p = 0.004). The significant correlation between BPb and HPb suggests the usefulness of hair for assessing occupational exposure particularly when the study area presents medium to high levels of Pb pollution. The association between Pb biomarkers and potential confounding factors revealed significant influence of the occupational factor over smoking and alcohol consumption. The results of this study urge for the reinforcement of the implemented engineering controls and safety measures in order to reduce exposure and to address the health issues related to Pb poisoning.

Evaluation of the status and the relationship between essential and toxic elements in the hair of occupationally exposed workers.

Lead poisoning is a common disease in lead-acid battery manufacturing industries. Workers can be also exposed to various toxic elements present as contaminants or used as catalysts to enhance batteries' performances. In the present study, levels of essential and toxic elements and their relationship were assessed by analyzing scalp hair samples of 52 workers in a Pb battery manufacturing plant. The impact of some confounding factors on hair mineral contents was also investigated. For comparative purposes, nonoccupationally exposed subjects were selected as controls. All elements were determined by triple quadrupole ICP-MS. The results indicated significantly higher levels of Pb, Sb, As, and Cd in the hair of workers when compared to controls (p < 0.01). The Spearman correlation test revealed significant correlations between Pb/Cr, Pb/Mn, Pb/Ni, Pb/As, Pb/Se, Pb/Sb, Hg/As, Hg/Sn, Hg/Sb, Sb/Cr, Sb/As, Sb/Se, Sb/Cd, Sb/Sn, Sn/Cr, Sn/As, Sn/Cd, Cd/As, Se/Ni, As/Cr, Ni/Cr, Ni/Mn, and Mn/Cr in the hair of workers and Pb/Cr, Pb/Mn, Pb/Ni, Pb/Cd, Mn/Ni, Mn/Cd, Cd/Ni, As/Ni, Sn/Ni, Sb/Sn, and Hg/Sn in the hair of controls. Multiple linear regression analysis revealed linear dependence including Cr = f(Pb, Ni, Sb), Mn = f(Ni, Sb), Ni = f(Mn, Cr, -Cd) (Cd was negatively correlated, ß < 0), As = f(Sn, Sb, Hg), Se = f(Ni); Sn = f(As), Sb = f(As, Mn, -Hg, Sn, Se, -Ni) (Hg and Ni were negatively correlated), Hg = f(As, -Sb, Sn) (Sb was negatively correlated), and Pb = f(Cr). The result of this study can be very useful to explain the interactions between elements or for comparison studies when establishing reference ranges or monitoring elements in workplaces.

Suitable interface for coupling liquid chromatography to inductively coupled plasma-mass spectrometry for the analysis of organic matrices. 1 Theoretical and experimental considerations on solute dispersion.

Liquid chromatography (LC) hyphenated to a specific detection such as inductively coupled plasma-mass spectrometry (ICP-MS) is a technique of choice for elemental speciation analysis. However, various instrumental limitations may considerably reduce the expected sensitivity of the technique. Among those, we were interested by the solute dispersion into the interface located between LC and ICP-MS. The interface consists of a Sample Introduction System (SIS) and a possible flow-splitter prior to SIS. Flow splitting can be required in case of organic matrices to reduce the organic solvent amount entering plasma which may lead to plasma instabilities. Although extra-column dispersion is usually well taken into account with conventional UV detection it has been little studied in the context of LC-ICP-MS and moreover never quantified. Our objective is to assess the loss in column plates and hence in both separation quality and sensitivity which may be generated by the coupling of LC and ICP-MS in the specific case of organic matrices. In this first study, this is done (1) from a theoretical approach; (2) from 55 experimental studies reported in LC-ICP-MS and (3) from our experimental results highlighting the critical impact of the flow splitter on extra-column dispersion depending on both flow-rate and split ratio. It turns out by evaluating the 55 reported studies by means of theoretical calculations, that the loss in plates due to extra-column dispersion was most of the time beyond 50% and even often beyond 90%. Moreover, from our experiments, it has been shown that a very low split ratio (1:50) could generate an additional variance around 200 µL² which induces a loss in theoretical plate of 90% for ultra-high performance LC (UHPLC) column (5 cm × 2.1 mm, 1.7 µm).

Two-year survey of specific hospital wastewater treatment and its impact on pharmaceutical discharges.

It is well known that pharmaceuticals are not completely removed by conventional activated sludge wastewater treatment plants. Hospital effluents are of major concern, as they present high concentrations of pharmaceutically active compounds. Despite this, these specific effluents are usually co-treated with domestic wastewaters. Separate treatment has been recommended. However, there is a lack of information concerning the efficiency of separate hospital wastewater treatment by activated sludge, especially on the removal of pharmaceuticals. In this context, this article presents the results of a 2-year monitoring of conventional parameters, surfactants, gadolinium, and 13 pharmaceuticals on the specific study site SIPIBEL. This site allows the characterization of urban and hospital wastewaters and their separate treatment using the same process. Flow proportional sampling, solid-phase extraction, and liquid chromatography coupled with tandem mass spectrometry were used in order to obtain accurate data and limits of quantification consistent with ultra-trace detection. Thanks to these consolidated data, an in-depth characterization of urban and hospital wastewaters was realized, as well as a comparison of treatment efficiency between both effluents. Higher concentrations of organic carbon, AOX, phosphates, gadolinium, paracetamol, ketoprofen, and antibiotics were observed in hospital wastewaters compared to urban wastewaters. Globally higher removals were observed in the hospital wastewater treatment plant, and some parameters were shown to be of high importance regarding removal efficiencies: hydraulic retention time, redox conditions, and ambient temperature. Eleven pharmaceuticals were still quantified at relevant concentrations in hospital and urban wastewaters after treatment (e.g., up to 1 µg/L for sulfamethoxazole). However, as the urban flow was about 37 times higher than the hospital flow, the hospital contribution appeared relatively low compared to domestic discharges. Thanks to the SIPIBEL site, data obtained from this 2-year program are useful to evaluate the relevance of separate hospital wastewater treatment.

Compartmentalization and ultrastructural alterations induced by chromium in aquatic macrophytes.

The aim of the present study was to identify the sites of accumulation of Cr in the species of macrophytes that are abundant in the Cachoeira river, namely, Alternanthera philoxeroides, Borreria scabiosoides, Polygonum ferrugineum and Eichhornia crassipes. Plants were grown in nutritive solution supplemented with 0.25 and 50 mg l(-1) of CrCl(3)·6H(2)O. Samples of plant tissues were digested with HNO(3)/HCl in a closed-vessel microwave system and the concentrations of Cr determined using inductively-coupled plasma mass spectrometry (ICP-MS). The ultrastructure of root, stem and leaf tissue was examined using transmission electron microscopy (TEM) and secondary ion mass spectrometry (SIMS) in order to determine the sites of accumulation of Cr and to detect possible alterations in cell organelles induced by the presence of the metal. Chromium accumulated principally in the roots of the four macrophytes (8.6-30 mg kg(-1) dw), with much lower concentrations present in the stems and leaves (3.8-8.6 and 0.01-9.0 mg kg(-1) dw, respectively). Within root tissue, Cr was present mainly in the vacuoles of parenchyma cells and cell walls of xylem and parenchyma. Alterations in the shape of the chloroplasts and nuclei were detected in A. philoxeroides and B. scabiosoides, suggesting a possible application of these aquatic plants as biomarkers from Cr contamination.

Heat-treated Saccharomyces cerevisiae for antimony speciation and antimony(III) preconcentration in water samples.

An analytical method was developed for antimony speciation and antimony(III) preconcentration in water samples. The method is based on the selective retention of Sb(III) by modified Saccharomyces cerevisiae in the presence of Sb(V). Heat, caustic and solvent pretreatments of the biomass were investigated to improve the kinetics and thermodynamics of Sb(III) uptake process at room temperature. Heating for 30 min at 80 degrees C was defined as the optimal treatment. Antimony accumulation by the cells was independent of pH (5-10) and ionic strength (0.01-0.1 mol L(-1)). 140 mg of yeast and 2h of contact were necessary to ensure quantitative sequestration of Sb(III) up to 750 microg L(-1). In these conditions, Sb(V) was not retained. Sb(V) was quantified in sorption supernatant by inductively coupled plasma mass spectrometry (ICP-MS) or inductively coupled plasma optical emission spectrometry (ICP-OES). Sb(III) was determined after elution with 40 mmol L(-1) thioglycolic acid at pH 10. A preconcentration factor close to nine was achieved for Sb(III) when 100mL of sample was processed. After preconcentration, the detection limits for Sb(III) and Sb(V) were 2 and 5 ng L(-1), respectively, using ICP-MS, 7 and 0.9 microg L(-1) using ICP-OES. The proposed method was successfully applied to the determination of Sb(III) and Sb(V) in spiked river and mineral water samples. The relative standard deviations (n=3) were in the 2-5% range at the tenth microg L(-1) level and less than 10% at the lowest Sb(III) and Sb(V) tested concentration (0.1 microg L(-1)). Corrected recoveries were in all cases close to 100%.

Speciation of selenium in a commercial dietary supplement by liquid chromatography coupled with inductively coupled plasma-mass spectrometry (ICP-MS).

Size exclusion and anion-exchange chromatographies coupled with inductively coupled plasma-mass spectrometry (ICP-MS) were used for the speciation of selenium (Se) in a dietary supplement. A sequential extraction method resulted in 85% recovery of Se and 78% of the Se extracted could be identified. The results obtained show that selenomethionine and its oxide are the predominant compounds, while selenite and selenomethylcysteine are present at low concentrations. Methane seleninic acid, probably arising from the oxidation of selenomethylcysteine, accounted for 22% of total Se. High-molecular-weight compounds, probably proteins, were detected in sodium dodecyl sulfate (SDS) and driselase extracts by size exclusion chromatography.

Extracellular production of hydrogen selenide accounts for thiol-assisted toxicity of selenite against Saccharomyces cerevisiae.

Administration of selenium in humans has anticarcinogenic effects. However, the boundary between cancer-protecting and toxic levels of selenium is extremely narrow. The mechanisms of selenium toxicity need to be fully understood. In Saccharomyces cerevisiae, selenite in the millimolar range is well tolerated by cells. Here we show that the lethal dose of selenite is reduced to the micromolar range by the presence of thiols in the growth medium. Glutathione and selenite spontaneously react to produce several selenium-containing compounds (selenodiglutathione, glutathioselenol, hydrogen selenide, and elemental selenium) as well as reactive oxygen species. We studied which compounds in the reaction pathway between glutathione and sodium selenite are responsible for this toxicity. Involvement of selenodiglutathione, elemental selenium, or reactive oxygen species could be ruled out. In contrast, extracellular formation of hydrogen selenide can fully explain the exacerbation of selenite toxicity by thiols. Indeed, direct production of hydrogen selenide with D-cysteine desulfhydrase induces high mortality. Selenium uptake by S. cerevisiae is considerably enhanced in the presence of external thiols, most likely through internalization of hydrogen selenide. Finally, we discuss the possibility that selenium exerts its toxicity through consumption of intracellular reduced glutathione, thus leading to severe oxidative stress.

Economic bismuth-film microsensor for anodic stripping analysis of trace heavy metals using differential pulse voltammetry.

Stripping analysis has been widely recognised as a powerful tool in trace metal analysis. Its remarkable sensitivity is attributed to the combination of a preconcentration step coupled with pulse measurements that generate an extremely high signal-to-background ratio. Mercury-based electrodes have traditionally been used to achieve high reproducibility and sensitivity in the stripping technique. Because of the toxicity of mercury, however, new alternative electrode materials are highly desired, particularly for on-site monitoring. Use of thin films of bismuth deposited on platinum or glassy-carbon substrates has recently been proposed as a possible alternative to mercury--bismuth is "environmentally friendly", of low toxicity, and is in widespread pharmaceutical use. In this paper the preparation of economic bismuth-film microelectrodes by electrodeposition on a copper substrate and their application to heavy metal analysis are described. Bismuth-film electrodes were prepared by potentiostatic electrodeposition. Optimum conditions for chemical and electrochemical deposition to obtain an adherent, reproducible, and robust deposit were determined. The suitability of such microelectrodes for analysis of heavy metals was evaluated by anodic stripping voltammetry of cadmium. The analytical performance of bismuth-film electrodes for anodic stripping voltammetry of heavy metals was evaluated for non-deaerated solutions containing Cd2+, Pb2+, and Zn2+ ions. Well-defined peaks with low background current were obtained by use of differential pulse voltammetry. Linear calibration plots were obtained for Cd2+ in acidified tap water at concentrations ranging from 2 x 10(-8) to 1 x 10(-7) mol L(-1) and from 1 x 10(-7) to 1 x 10(-6) mol L(-1) with relative standard deviations of 5% (n = 15) at the 1 x 10(-7) mol L(-1) level. The method was then successfully used to monitor the Cd2+ content of plant extracts and validated by polarographic and ICP-MS measurements. These results open the possibility of using bismuth-coated copper electrodes as an alternative to mercury-based electrodes for analysis of heavy metals. The main problem remaining, which prevents on-site monitoring of heavy metals, is the need to use slightly acidic media, because formation of bismuth hydroxide on the film surface above pH 4.3 leads to non-reproducible measurements. Further experiments will be performed to discover whether electrode conditioning can be used to enable reproducible measurement in on-site monitoring of cadmium in natural waters. Moreover, further study should be conducted to evaluate the potential of BiFE for analysis of several pollutants of interest that are usually determined electrochemically by using mercury-based electrodes.